Recommended Components: Fall 2020 Edition Power Amps

Two-Channel Power Amplifiers

Editor's Note: Because of the disparity between typical tube and solid-state "sounds," we have split Class A for separate power amplifiers into two subclasses. Nevertheless, even within each subclass, Class A amplifiers differ sufficiently in character that each will shine in an appropriate system. Careful auditioning with your own loudspeakers is therefore essential. Except where stated, output powers are not the specified powers but rather those we measured into an 8 ohm resistive load. All amplifiers are stereo models, except where designated.

A (Solid-State)

Bel Canto Design e.One REF600M monoblock: $4990/pair $$$ ★
Bel Canto's REF600 monoblock is similar in size to their REF1000M, which KR reviewed in the March 2009 issue, but the newer amp trades the older's ICEpower-based class-D output section for the newly ubiquitous Hypex NCore class-D module, which develops 300W into 8 ohms or 600W into 4 ohms—specs identical to those of the MPS1 power-amp section of the Bel Canto Black (described elsewhere in this edition of "Recommended Components"). Of his experience with the REF600Ms driving his Bowers & Wilkins 802 D3 loudspeakers, KR observed that they "never ran out of steam with any sort of music at any listening level, and remained absolutely consistent in tonal balance and clarity." Kal also described the amp's price as "eye-openingly" low. JA's measurements uncovered a remarkably high (109.9dB) unweighted signal/noise ratio, power outputs higher than the manufacturer's specs, and "impressively low levels of distortion and noise." In a Follow-Up in September 2017, HR reported on his experience with the Bel Canto monoblocks, ostensibly borrowed to drive his current-hungry Magnepan .7s (which Herb had never heard sound "more precise, powerful, or three-dimensional" than with the post-break-in REF600Ms). After trying them with five different loudspeaker models, he wrote, "the Bel Cantos offered up weight, body, punch, and crystalline detail better than some of the most expensive amplifiers I know." (Vol.39 No.10, Vol.40 No.9 WWW)

Bel Canto e1x: $6000
Trickled down from Bel Canto's premium Black line, this slimline, lightweight amplifier uses the well-regarded Ncore class-D modules and a low-noise switch-mode power supply. TG commented positively on the e1x's image specificity, low-frequency control, and extremely low background noise. "I didn't expect to be so completely gobsmacked by the level of clarity and musicality I'm hearing now from the e1X," he concluded. JA's measurements revealed that the Bel Canto easily exceeded its rated output powers of 250Wpc into 8 ohms and 500Wpc into 4 ohms, clipping at 340Wpc into 8 ohms and at 530Wpc into 4 ohms. Noise, harmonic distortion, and intermodulation distortion were all impressively low in level. (Vol.43 No.6 WWW)

Benchmark AHB2: $2999 $$$ ★
Named for the late Allen H. Burdick, the engineer whose work formed the basis for its design, Benchmark's AHB2 makes use of THX Corporation's Achromatic Audio Amplifier (AAA) technology, in which a low-power feed-forward amplifier drives a low-bias class-AB output section. In his listening tests KR discovered "much more apparent low-level detail in already-familiar recordings"—a characteristic he credited to the Benchmark's evident noiselessness—and a tonal balance that "sounded more 'right' than any of [the other amps on hand]." In measuring the AHB2 and attempting to confirm its specified (very) high signal/noise ratio, JA observed nonlinearities in his testing equipment that "haven't affected the measured performance of other amplifiers I've tested, but they were detectable with the AHB2's very low intrinsic distortion and noise." His conclusion: "an extraordinary amplifier." In his Follow-Up report JCA described comparing the AHB2 to his reference amp: "Although I preferred the AHB2's denser presentation of certain details, it's not clear to me which is truer to the source." (Vol.38 No.11, Vol.41 No.10 WWW)

Boulder Amplifiers 2150 monoblock: $110,000/pair ★
The new 2150 monoblock—it replaces Boulder's 2050 monoblock, introduced in 2000—is among those relatively recent designs that operate in class-A for their full rated power, yet do so by means of microprocessor-based circuits that continually adjust bias in response to current draw, load, and other parameters. Consequently, the 2150 runs relatively cool. Each 2150 uses global feedback (proudly: its manufacturer suggests that manufacturers who don't use feedback simply don't know how to do so properly), boasts an output section containing 80 bipolar devices, requires an AC cord compatible with its 32A IEC socket, has heatsinks machined into the sides of its chassis, and weighs an extraordinary 220lb (319lb in its shipping crate). For all that bigness, the Boulder amp kept out of MF's way, sonically: "It was about as tonally neutral a piece of electronics as I've heard here, neither warm nor cool." MF also praised the Boulder's "unrestricted microdynamic excursions" and its "well-controlled, ultra-solid, well-defined low-frequency response." Writing from his test bench, JA noted that the difficult-to-move Boulder "measured so well that it taxed the capabilities of my Audio Precision SYS2722." (Vol.40 No.2 WWW)

Bricasti Design M15 Stereo Amplifier: $15,000
With its CNC-machined aluminum case and its purposeful-looking feet—the latter presumed by JVS to discourage the use of ancillary isolation products—the 90lb Bricasti M15 stereo amplifier evinces the DNA of its similarly chunky stablemate, the M28 monoblock. Like that older amp, the solid-state M15 is fully balanced—both single-ended (RCA) and balanced (XLR) inputs are provided—and operates in class-AB. It's fully analog, using traditional power-supply technology, and each channel's output section employs 24 bipolar output devices, for a specified power output of 125Wpc into 8 ohms. JVS praised the Bricasti's "colorful if toned-down" sound and, with some music, heard "excellent three-dimensionality," but felt that on some recordings strings "lacked shine," while others "felt diminished by the muzzled bite of percussion." Still, he noted in his conclusion that the M15 "could be just what the doctor ordered" for a system or room that tends toward the harsh or the bright. JA's measurements suggested that the Bricasti "comfortably exceeded" its specified power output, but was surprised when the amp shut down while being tested into a low-impedance load: "It is clearly less happy driving 2 ohms than it is higher impedances." See also JA's Constellation review in Vol.41 No.10. (Vol.41 Nos.7 & 10 WWW)

CH Precision M1.1: $104,000/pair
The Swiss-made CH Precision M1.1 is a modular solid-state amp—the user can configure the amp for stereo or mono use, as well as for a choice of output-power-delivery modes—with a JFET front end and a class-AB output stage. A robust power supply built around a massive 2200VA transformer helps account for the M1.1's extraordinary (165lb) weight. MF, who found the amp's timbral balance to be very slightly on the warm side of neutral, was taken with a pair of M1.1s configured for mono, noting that their richness did not come with the penalty of softened transients and praising the amps' combination of bass depth and bass kick. In measuring the M1.1, JA observed that its performance on the bench was dependent upon the amount of distortion dialed in (MF preferred the sound at 20%) and noted the amp's preference for loads higher than 2 ohms. (Vol.42 No.7 WWW)

Classé Delta Mono monoblock: $21,998/pair
The first fruits of the Canadian company's acquisition by Sound United, the Delta series products were in development for several years. Designed in Canada but made in SU's Japanese factory, where the high-end Denon and Marantz products are manufactured, the Delta Mono impressed JA not only with its sound quality but also with its impeccable construction. The front panel features an accurately calibrated VU meter. With its lateral-MOSFET output devices heavily biased into class-A, the Delta Mono's waste heat is expelled from its rear with a quiet-running, microprocessor-controlled fan. "The midrange transparency of the Classé amplifiers was impressive," wrote JA, adding that "the high frequencies were impressively clean and smooth" and that the Delta Mono exhibited tight low-frequency control and articulation. Compared with the Parasound Halo JC 1+s, the Delta Monos had a touch less bloom through the lower midrange. The Delta Mono exceeded its specified output power of 300W into 8 ohms and 600W into 4 ohms, clipping at 380W into 8 ohms and 610W into 4 ohms. Price includes high-quality DR Acoustics AC cables. (Vol.43 No.7 WWW)

Constellation Centaur II 500 Stereo: $70,000
For five times the price of their Inspiration Stereo 1.0 amplifier (see elsewhere in "Recommended Components"), Constellation Audio offers the Performance Centaur II 500 stereo amp, with 2.5 times the power (500Wpc into 8 ohms) and nearly three times the weight (150lb). As with a relative few of audio history's most distinguished solid-state amps, the Centaur uses all N-channel transistors; here, they're built into single-ended modules, themselves combined into what Constellation calls their Balanced Bridged topology. Both balanced (XLR) and unbalanced (RCA) inputs are provided, as is a switch allowing the user to bypass the amp's input-voltage gain stage, for systems in which the Performance Centaur II 500 is preceded by a Constellation preamp. Used to play a recording of Rachmaninoff's Symphony 1 through a review pair of Wilson Alexia Series 2 speakers, the Constellation provided JA with "a transparent window on the acoustic of the Amsterdam hall where the recording was made," with stable and appropriately scaled imaging of solo instruments. And with Tidal's mighty Akira speakers, the Constellation offered "superb" dynamics: "The timpani blows . . . rocked me back in my chair." Reporting from his test bench, JA noted the amp's significantly-lower-than-specified input impedance but also its slightly-higher-than-specified (550Wpc) power into 8 ohms. Quoth the editor: "a powerhouse of an amplifier." (Vol.41 No.10 WWW)

Constellation Inspiration Stereo 1.0: $14,000
Although casework machined from aluminum is far from rare among high-end power amplifiers, the enclosure of Constellation's Inspiration Stereo 1.0 is a slight but welcome departure from the norm, aesthetically and functionally: on each side of the amp are nearly 200 cooling holes machined into inner and outer side panels, the two panels offset so that the inner and outer holes don't quite line up with each other—a source of visual interest that apparently doesn't compromise the effectiveness of the internal heatsinks. Of far greater interest is this 200Wpc class-AB amp's sound quality, which LG described as "more vivid, refined, and transparent than my reference amps." LG also noted being impressed with the "speed, pitch definition, and harmonic balance" of instrumental sounds in the lowest octaves, though he reported that the lowest tones "didn't thunder or shake the room" as he might have wished. In measuring the Inspiration Stereo 1.0, JA observed higher-than-specified power output—340Wpc instead of the claimed 200Wpc—and praised the Constellation's "quite respectable measured performance." (Vol.41 No.4 WWW)

Dan D'Agostino Master Audio Systems Progression Monoblock: $38,000/pair ★
The star of Dan D'Agostino's Progression line of amplifiers—products only slightly less exalted than those in the company's Momentum line—the Progression Monoblock is actually D'Agostino's most powerful amplifier, delivering 500W into 8 ohms, 1000W into 4 ohms, or 2000W into 2 ohms. This class-AB amp retains D'Agostino's signature venturi heatsinks, in which a series of vertical holes is drilled straight through solid billets of aluminum. Each Progression Monoblock weighs a considerable 150lb and, as JVS discovered, tends not to run more than warm to the touch: "On colder days, I still needed to heat the room." JVS also discovered the Progression Monoblocks' fine performance: "Not only did [they] nail the savagery of the high-driving piccolos and brutal bass without breaking a sweat, they also kept every instrument in control and balance while conveying a realistic, airy soundstage." In measuring the Progression Monoblock, JA confirmed the amp's very high power output but discovered distortion products suggestive of low bias current in its output stage: curious for an amp from a designer famous for favoring class-A (ie, high-bias) architectures. (Vol.40 No.10 WWW)

DarTZeel NHB-468 monoblock: $180,000/pair
The darTZeel NHB-468 monoblock, which looks outwardly similar to its predecessor, the NHB-458, is claimed to be rather different on the inside, said changes including a technology called Constant Power to Current, or CP2C: a circuit that, according to darTZeel, "mimics a current source with the output impedance of a voltage source." The new amp retains the same massive power supply as the old, down to its enormous, spring-suspended mains transformer, yet most power specs are lower for the 468 than the 458 (eg, 475W into 8 ohms instead of 530W). The NHB-468 impressed NHB-458 owner MF with sound that was "more supple, more liquid, and noticeably more 'wraparound' three-dimensional, without turning soft." MF's verdict: "This amp does what the NHB-458 does—just better." Technical Editor JA noted that the new amp did not meet its power spec—he observed 398W into 8 ohms—but praised the fact that it does not exhibit increased distortion with rising frequency, saying the newest darTZeel is "an intriguing design." (Vol.42 No.11 WWW)

Lamm Industries M1.2 Reference monoblock: $33,990/pair ★
The 110W M1.2, with tubed front end, MOSFET output stage, comprehensive short-circuit protection, and high/low impedance settings, offered "unflinching honesty in conveying the true nature of the music that passed through it," said PB. "Utterly continuous and coherent from top to bottom," the M1.2 combined resolution and transparency with harmonic completeness, timbral richness, and glow. JA concurs. Compared to the Classé CT-M600 and MBL 9007, the Lamm had a more robust, less delicate sound, but nevertheless impressed JA with its three-dimensional soundstaging and midrange richness. "This is a great amplifier," he decided. "Highly recommended." In his follow-up, JCA observed that "the Lamms didn't bring out every tiny nuance . . . but, boy, are they musical! In that way, they deviate from the stereotype of a big-boy amp." (Vol.28 No.2, Vol.35 No.4, Vol.37 No.6, Vol.39 No.12, Vol.41 No.10, Vol.43 Nos.6 & 7 WWW)

LKV Research Veros PWR+: $10,000
This surprisingly massive, American-made amplifier powers its Purifi class-D output stage modules with a hefty linear power supply utilizing a hefty 1kVA toroidal transformer and two smaller transformers. Front-end and driver circuitry is based on paralleled discrete devices biased into class-A. HR wrote that "the class-D LKV amp played equally rich and atmosphere-soaked through the entire audio band. It did atmospheric dreamy like class-A does atmospheric dreamy." He found that every recording he played with the Veros PWR+ sounded "richer and wetter (atmospherically) than class-D is supposed to." In the test lab, the LKV amplifier exceeded its specified power of 200W into 8 ohms, clipping at 221Wpc with both channels driven, while it delivered the specified 400Wpc into 4 ohms. With one channel driven, the clipping power into 2 ohms was 505W. Noise and distortion levels were both very low, and the distortion signature was almost pure third-harmonic in nature. (Vol.43 No.9 WWW)

Mark Levinson No.534: $20,000
The 350Wpc, class-AB No.534 stereo amp can be seen as a less expensive alternative to Mark Levinson's 400W No.536 monoblock (see below). In fact, apart from the balanced bridge topology of the No.536, which enables its separate banks of bipolar power transistors to function together in driving a single loudspeaker, and the very different parts counts and circuit layouts in their input and driver boards, a No.534 and a single No.536 are very much alike. LG spent time with both, and declared the No.534 "a compelling stereo amplifier" with a "tirelessly wide" dynamic range and the ability to "easily [reproduce] the deepest bass chords of pipe-organ recordings." His verdict: "the No.534 delivers the No.536's sound and build quality at two-thirds the price." (Vol.41 No.5 WWW)

Mark Levinson No.536 monoblock: $30,000/pair ★
The class-AB, 400W (into 8 ohms) No.536 is distinguished by many of the same technical characteristics seen in other recent Mark Levinson products, including a direct-coupled, fully discrete signal path and the fact that, while the No.536 uses some negative feedback, its overall gain structure is designed for linear open-loop performance before that feedback is applied. Each monoblock contains two fully differential output stages in a bridged configuration claimed to bolster current output and maintain stability into very low-impedance loads, and the No.536 is specified as operating in pure class-A up to 3W. LG praised the No.536 for exerting "a superior grip" on the woofers of his Revel Ultima Salon2 speakers, and for reproducing deep organ-pedal notes "with unflinching control and solidity." Larry also noted that "the midrange blossomed when my speakers were driven by the No.536es," and pointed to their ability to throw "a wide, deep soundstage." LG's conclusion: The No.536 is "equaled by only one or two other amplifiers in memory." JA's summary: "Overall, the Mark Levinson No.536 measured very well, its performance uncompromised by its ability to deliver very high powers into low-impedance loads." (Vol.40 No.7 WWW)

mbl Corona C15: $20,000/pair ★
Although it employs a custom-specified version of the popular Hypex class-D amplifier module, the Corona C15 monoblock, which offers 280W into 8 ohms, 520W into 4 ohms, is, according to its designer, a "Linear Analog Switching Amplifier," the overall design concept of which entails the use of a linear rather than switch-mode power supply—itself built around a toroidal transformer with generous mu-metal shielding. (The latter is presumed to contribute to the amp's 48.5lb weight.) Indeed, in his measurements, JA confirmed that "the C15's transfer function appears to remain relatively consistent with both frequency and output current"; also unusual for a class-D amp was the C15's admirable output-impedance behavior: JA discovered that its low-pass function into loads of 4 and 2 ohms was "very similar to its 8 ohm behavior." In his listening tests, JA found that the C15's "intrinsic character was all about control, especially the tight control of low frequencies"—a quality that served well the amp's pairing with the somewhat rich-sounding woofer alignment of the Vivid Giya G3 speaker, but less so the Joseph Audio Perspective, with which the MBL sounded clean but lean. Especially when combined with the classic Rogers LS3/5a, JA observed "superb imaging definition and stability" with the good-looking MBL amps. (Vol.37 No.6 WWW)

McIntosh MC462: $9000
As of this writing the most powerful stereo amplifier in the McIntosh line, the solid-state MC462 is rated at 450Wpc into 2, 4, or 8 ohms, and weighs a floorbending 115lb. The output section is class-AB, designed so that each individual phase of the signal waveform is amplified by a complete push-pull output section; there are two complete push-pull amps in each channel, their outputs combined—using autoformers—in what McIntosh refers to as a Quad Balanced architecture. SM praised the Mac for delivering, without strain, a piano sound faithful to the original, for portraying brass instruments, drums, and other instruments with appropriate force, impact, and, when called for, swing. As for value, SM opined that "$9000 is more than fair for the excellence delivered." Reporting from his lab, JA declared that the MC462 is "an extraordinarily well-engineered, exceptionally powerful amplifier." (Vol.42 No.5 WWW)

Moon by Simaudio 888 monoblock: $118,888/pair
For our reviewers, 2018 was The Year of Lifting Dangerously: first the 255lb EgglestonWorks Viginti loudspeaker, then the 300lb ASR Emitter II Exclusive integrated amp, and now the 250lb Moon by Simaudio 888 monoblock—500lb per stereo pair! In the Moon's case (haw), much of that weight comes from the massive, elaborate, one-piece aluminum castings that comprise the amp's side panels, each one enfolding, damping, and heatsinking the 32 output transistors per channel. Each Moon 888 also includes two massive, potted power transformers, 12 big, custom-made power-supply storage capacitors, and a cast-aluminum chassis capable of supporting all of the above. With the 888W (into 8 ohms), class-AB Moons in his system, MF delighted in "the highest level of sound quality in my system, passing along warmth or chills, transparency or sludge, grain or greatness, as dictated not by the electronics but by the recording itself." We can't tell you how the 888 fared on JA's test bench because it was too heavy to make the trip—John packed up his battery of test gear and measured the amp chez Mikey, where he confirmed its low impedance, high output power (he measured not 888W but 990W), "excellent" in-audioband signal/noise ratio, and overall "good measured performance." (Vol.41 No.8 WWW)

Parasound A 21+: $2995
The successor to the Parasound A 21, the new A 21+ offers 300Wpc into 8 ohms, compared with its predecessor's 250Wpc—and the new model, which operates in class-AB, can be bridged to serve as a 1000W monoblock. Other refinements include a gruntier power transformer, brawnier speaker connectors, an increase in power-supply filter capacitance, and other niceties. Balanced (XLR) and unbalanced (RCA) inputs are both provided, as are dual-mono level controls. According to KR, "listening to the A 21+ was eminently delightful and satisfying from the first note," and he pointed to the new amp's "transparency without highlighting or emphasis" and the manner in which it handled dynamic challenges in orchestral music "without stress." Technical Editor JA found that the A 21+ exceeded its power specs, delivering a full 400Wpc into 8 ohms, and noted that the amp "isn't fazed by impedances as low as 2 ohms." (Vol.43 No.3 WWW)

Parasound Halo JC 1+ monoblock: $16,990/pair
A replacement for the long-term "Recommended Components" resident, the original Halo JC 1, the 1+ represents designer John Curl's further thoughts on this powerful solid-state monster. While more expensive in real terms than its predecessor, the Halo JC 1+ is 30% heavier, still heavily biased into class-A, and offers slightly more power than the original amplifier: 450W into 8 ohms, 850W into 4 ohms, and 1300W into 2 ohms. Bass guitar and kickdrum were reproduced with appropriate force and definition, felt JA, exclaiming, "Low-frequency power and delicacy!" JA was also impressed by the pair of monoblocks' ability to differentiate soundstage depth and described the Parasound's high frequencies as sounding "more like what I experience from a good tube amplifier." "This is a superb-sounding amplifier that will get the best from every loudspeaker with which it is partnered," JA concluded, adding "Well done, Mr. Curl." On the test bench, the Halo JC 1+ exceeded its specified power into 8 ohms, clipping at 500W. It didn't quite meet its specified power into lower impedances, clipping at 830W into 4 ohms and at 1200W into 2 ohms, though JA did note that the slight shortfall was due to him not holding the AC wall voltage constant in the testing. Commendably, the JC 1+'s distortion was predominantly the subjectively innocuous second harmonic, though at a very low level. (Vol.43 Nos.6 & 7 WWW)

Pass Laboratories XA200.8 monoblock: $42,000/pair
That a single Pass XA200.8 monoblock should weigh almost precisely the same as the average European adult (it won't catch up with the average North American adult for another 20lb) should come as no surprise: This is a 200W (into 8 ohms) amplifier that operates in class-A, and does so without any sort of microprocessor-controlled sliding-bias scheme. That takes big heatsinks and a good deal of design cunning, and the XA200.8 shows evidence of both, the latter in its DC-coupled front end and distinctive application of input-stage feedback, the former in its . . . well, in its big heatsinks. JVS, who found himself wearing a back brace by the time he'd packed up the review samples and sent them away, agreed with those visitors who described the sound of the XA200.8 as "organic." He wrote that the Passes seemed to "illuminate music from within" in a way that complemented the artistic brilliance of the musicians. He noted the XA200.8's lack of sweetening or softening, and concluded by praising it as "a masterpiece of amplifier design." After measuring the XA200.8, JA expressed his belief that it lacked sufficient bias current to operate in class-A for its full output power, yet nonetheless praised it for its "well-balanced audio engineering." (Vol.41 No.8 WWW)

Pass Laboratories XA25: $4900
The lowest-priced amplifier in Pass Laboratories' XA series, the XA25 strips away all inessentials—front-panel meters, balanced inputs, excessive output power—and provides the listener with a three-stage amplifier in which output power is generated by a single pair of transistors per channel, operating in push-pull class-A. Output is specified as 25Wpc into 8 ohms or 50Wpc into 4 ohms. HR tried the Pass with a great variety of speakers, starting with a rebuilt pair of original Quad ESL electrostatics: "Through the Quads, the XA25 radically improved the tactile presence of music and musicians, their voices and instruments," he wrote. "It made the Quad's legendary midrange more solid, dynamic, and well defined than I'd ever thought possible." Another, very different panel speaker came next: "Driven by the Pass Labs XA25, the Magnepan .7s did real-life natural with ease and élan." Additionally, HR found, "bass weight and organ power were well reproduced by a speaker not famous for these traits." But even that pales in comparison to Herb's adventures using the Pass amp to drive his DeVore Orangutan O/93s: "I began to realize that the XA25 is the most transparent amplifier I've ever heard." His verdict: "reasonably priced, strong beyond its power rating, and positively revelatory." Writing from his laboratory, JA noted that the Pass far exceeded its rated power output, concluding that "the XA25 performed well on the test bench, as I've come to expect from Pass Labs." (Vol.41 No.2 WWW)

Pass Laboratories XA60.8 monoblock: $13,500/pair
In reviewing Pass Laboratories' solid-state XA60.8 monoblock amplifier, JCA echoed JA's earlier published response to the amp's predecessor, the XA.60.5: "the best amplifier I've heard." Each 88lb XA60.8 operates in pure class-A, made possible in part by the amp's massive aluminum heatsinks and no-less-massive steel mains transformers. (Indeed, the most obvious change from XA60.5 to XA60.8 is a weight increase of 22lb—per channel.) Output is specified as 60W into 8 ohms, doubling to 120W into 4 ohms. JCA thought the Passes sounded "sweeter, warmer, more delicate" than the more expensive monoblocks that preceded them in his system, but reserved his greatest praise for their spatial prowess: "I'd never heard an amplifier make such an obvious difference. . . . To walk into this room while a good recording was playing was to enter an immersive aural apace." JA, now acting as measurer rather than reviewer, wrote from his test bench that the "well-engineered" XA60.8 "considerably exceeded" its rated output power, delivering 150W into 8 ohms at 1% THD, and he praised its A-weighted signal/noise ratio of 93.6dB: "This is a quiet amplifier." JCA's conclusion: "I am smitten." (Vol.40 No.12 WWW)

Primare A35.2: $3495
This hefty Danish amplifier uses what Primare calls their "proprietary UFPD2 analogue class-D amplification technology" to deliver 200Wpc into 8 ohms. According to the manufacturer, UFPD2 integrates the class-D output stage and the necessary low-pass filter, "making control with feedback much more immediate and accurate." HR found that with his Magnepan .7 speakers, the A35.2 sounded very similar to the slightly more expensive Bel Canto REF600M class-D monoblocks. He wrote that the A35.2 "gripped the Magnepans' diaphragms with greater control and force than either the class-A Pass Labs XA25 ($4900) or the $3495 all-tube, class-AB Rogue Stereo 100 (in Ultralinear mode). This control delivered a tauter, more rhythmic bass." With Harbeth M30.2 speakers, HR found that the Primare's high frequencies were "crisp and super-clear—but not luxuriant and engaging." On the test bench, the Primare exceeded its specified powers, clipping at 225Wpc into 8 ohms and at 460Wpc into 4 ohms. (Vol.43 No.5 WWW)

PS Audio BHK Signature 300 monoblock: $14,998/pair ★
Named for its designer, Bascom H. King, the BHK Signature 300 is a hybrid monoblock with a tubed input stage and a MOSFET power stage, and is specified to deliver 300W into 8 ohms. In a departure from the usual practice, all of those output transistors are n-channel devices, implementation of which requires cunning—and, according to King, a bit of global feedback. Both single-ended (RCA) and balanced (XLR) inputs are provided on the rear panel, where one also finds a removable panel for access to the amp's two dual-triode tubes. In MF's words, "the BHK Signature 300 is a powerful, nimble-sounding amplifier that immediately drew me in with fast, punchy, tight bass; rich, liquid mids; and delicate, transparent highs—all effectively well integrated into a coherent whole." On JA's test bench, one of the BHK Signature 300 monoblocks became unstable, and while it didn't fall and break its hip, it stopped working. JA carried on with the other monoblock, describing it as "a well-designed, well-engineered powerhouse of an amplifier, though it will perform at its best with speakers having an impedance of 4 ohms and above." In 2017, JCA embarked on an interesting pairing—PS Audio's "big brute" amps with the sensitive, easy-to-drive DeVore Fidelity Orangutan O/96 speakers—and discovered that while the DeVores didn't necessarily benefit from such a surplus of power, he "slightly preferred the BHKs' weight" to the "airier, spacier" sound heard with his Leben tubed integrated amp. (Vol.39 No.2, Vol.40 No.8 WWW)

PS Audio Stellar M700 monoblock: $2998/pair $$$
The Stellar M700 incorporates the latest version of PS Audio's Gain Cell—described as "a proprietary, fully differential, zero feedback, discrete, class-A MOSFET circuit"—using it to drive a class-D power module from the Danish ICEpower company. The Stellar M700 has both balanced (XLR) and single-ended (RCA) inputs, weighs a mere 13lb, and is specified as providing 350W into 8 ohms. RD used a pair of M700s to drive his Monitor Audio Platinum PL300 II loudspeakers, and described the amp as having "very little sound of its own, and nothing that I could describe as a distinct class-D character." The PS amps impressed RD with their distinctly smooth sound—"tubelike wouldn't be entirely inappropriate as a description"—and noted that they were able to drive the Monitor speakers "to volume levels as high as I could tolerate without amplifier or speakers ever sounding distressed." In measuring the Stellar M700, JA noted that it slightly exceeded its rated power output, and concluded that it "offers respectable measured performance." (Vol.41 No.2 WWW)

Schiit Aegir: $799 $$$
The solid-state Aegir amplifier uses a proprietary class of operation called Continuity, which gets around certain limitations of class-AB operation—particularly transconductance droop beyond the class-A power envelope—by means of a current-feedback topology. It's specified at 20Wpc into 8 ohms and 40Wpc into 4 ohms and runs a bit hot—but not as hot as one might expect from a pure class-A amp of the same output. HR described the "titillating physical pleasures" of the made-in-California Aegir driving Wharfedale Linton loudspeakers as something he could "live [with], satisfied, forever," and praised the pairing of Schiit Aegir and Harbeth P3ESRs as offering "80% of the . . . detail-rich humanity" he hears from his $4000 reference amplifier. In measuring the Aegir, JA found higher than specified output power—28Wpc into 8 ohms, 43Wpc into 4 ohms—and described the Schiit as "a well-engineered amplifier at an affordable price." Herb's conclusion: "a design that will withstand and even rejoice in the scrutiny of time." (Vol.42 No.10 WWW)

Vandersteen Audio M5-HPA: $16,800/pair
Class A rating applies to use with Vandersteen speakers or minimonitors. (Vol.42 No.11 WWW)

Verity Audio Monsalvat Amp-60: $58,000
The Monsalvat Amp-60 differs from other premium-priced solid-state amps in a key way: Verity Audio set out to create not an ultra-high-power amp—something the Amp-60's designers regard as involving "compromises that hinder the quality of the sound"—but rather to make a more modestly powered amplifier. Thus the Amp-60 delivers 60Wpc into 8 ohms and 120Wpc into 4 ohms. Driving JVS's Wilson Alexia 2s, the Verity amp "began weaving a web of seduction" from the first track he played, with a "velvet smooth" midrange in which individual sonic texture maintained their characters—although, on a recording of a Mahler symphony, "the sound lacked oomph" and the work's "big bass poundings shook the room less" than he wished. In measuring the Monsalvat Amp-60, JA discovered that, counterintuitively, the amp's balanced inputs yielded lower S/N ratios than its single-ended inputs. Also, although he found higher-than-specified output power (95Wpc) into 8 ohms, JA observed that the Amp-60 clipped at just 50Wpc into 2 ohms. (Vol.42 No.5 WWW)

Ypsilon Hyperion monoblock: $93,000/pair
The 209lb Hyperion monoblock is a two-stage hybrid design with a low-impedance dual-triode tube for its input stage—a 6H30 or a 5687 will do—and MOSFETs for its output section. The two stages are joined by a custom-wound transformer that also serves as the phase splitter for the push-pull output architecture, and the amp is fitted with a 6CA4/EZ81 rectifier tube—an oddity in an otherwise predominantly solid-state product. Output power is specified as 370W into 8 ohms, with the first 100W assured as being in class-A, and 650W into 4 ohms. As for the influence of that input tube, MF found that "the Hyperion's additive quality wasn't . . . identifiable as what's usually thought of as tube sound, but rather as a subtle harmonic and textural generosity that I think most listeners would find very pleasing." Mikey added that "the Hyperion strikes the ideal balance between tube-amp richness and flow and solid-state quiet, authority, and dynamic swagger," and proclaimed it "among . . . the best-sounding power amplifiers I've heard, and it's the most musically enjoyable of the lot." JA, writing from his test bench, painted a somewhat different view, having found an ultrasonic response peak, a linear increase in distortion with increasing power output, and a failure to meet the power-output specs with less than 2% THD. (Vol.41 No.4 WWW)

A (Tube)

Air Tight ATM-300R: $18,500 with Electroharmonix 300B tubes
AD, who was on record as having "never heard a single-ended 300B amp that I disliked," was especially smitten by this compact yet remarkably heavy (54lb) stereo amplifier: a three-stage design in which 12AU7 and 12BH7 dual-triodes are used as voltage-gain stages and drivers, respectively. The output tubes are a single 300B per channel, specified to output 9W each. Distinctively, the ATM 300R uses global feedback, but tapped from the primary rather than secondary side of each channel's output transformer. AD heard from the Air Tight amp "startling . . . details of musical nuance," "lusciously textured and colorful" strings and woodwinds, "realistic force" in its reproduction of timpani, and the ability to sound surprisingly big. He also made special mention of the ATM 300R's way with orchestral double-basses, noting their "depth and power, and far greater clarity of pitch than I've heard through any other 300B amplifier, bar none." Re-auditioning the amp in his newly modified listening room, through vintage Altec Flamenco loudspeakers, confirmed those positive impressions, and then some. Writing from his test bench, JA described the Air Tight as "well engineered," praising in particular its apparently "excellent output-transformer design." (Vol.41 No.2, Vol.42 No.11)

Audio Research Reference 160 S: $20,000
Essentially a stereo version of ARC's Reference 160 M monoblock, the Reference 160 S uses four KT150 output tubes per channel to deliver 70Wpc into 8 ohms in triode mode or 140Wpc in Ultralinear, the two being switch-selectable. The user can also select between balanced (XLR) and unbalanced (RCA) inputs, the latter a first for an ARC Reference-series amp, and speaker outputs are provided for 4, 8, and 16 ohms. JCA enjoyed his time with the REF 160 S, particularly when assessing the differences between triode and Ultralinear: "In triode mode there was a fine velvet, burnished beauty. In Ultralinear . . . the music was more explicit—but the sound was just as lovely." Jim remarked, before the ARC amp left his home: I didn't know that so much of the music in my collection possessed so much tonal beauty." JA felt the amp's very low feedback should compel users to exercise careful load matching. (Vol.43 No.2 WWW)

Audio Research Reference 160M monoblock: $30,000/pair
The Reference 160M wrings 140W from a push-pull quartet of KT150 pentode tubes, operated in class-AB, with phase inversion and voltage gain provided by a pair of 6H30 dual-triode tubes. It also offers switch-selectable balanced and single-ended inputs—during testing, JA was surprised to see the latter mod of operation offered considerably more gain—and employs a modern auto-bias system. The REF 160M also allows the user to choose between Ultralinear and triode modes at the flip of a switch (in triode mode, the amp outputs 75W). With a pair of REF 160Ms driving his Wilson Alexia 2 floorstanders, JVS reported sound that was impressively "natural, full-range, and beautiful," including an ability to convey "hard-to-distinguish details and sonorities . . . with clarity." Writing from his test bench, JA reported evidence of only "a modest amount" of global feedback, and commendably higher-than-specified output power when operating in Ultralinear mode and speaking to the world through its 8 ohm outputs. (Vol.41 No.10 WWW)

BorderPatrol P21 EXD: $14,450 with 300B tubes
The BorderPatrol P21 EXD is a 300B amp with a twist: although its present-day reputation stems from its appearance in single-ended amplifiers, here the hallowed 300B output tube is used in pairs, for push-pull operation, producing what designer Gary Dews claims to be an output of 20Wpc. The EXD model reviewed by KM is an upgraded version of the company's basic P21, with better parts and cryogenic treatment of its copper chassis and interstage and output transformers. It is a fixed- rather than auto-bias design, does not employ global feedback, and has an outboard power supply that itself weighs a chunky 35lb—virtually as much as the amp itself. Used with DeVore Fidelity Orangutan O/93 and Klipsch Heresy III loudspeakers, the BorderPatrol amp provided KM with deep bass that was "tighter and tauter" than he hears from his Shindo Laboratory Haut-Brion (also push-pull, also 20Wpc), plus "super-'black' backgrounds, solid dynamics, excellent imaging, and a special way with texture and touch." Through the DeVores in particular, the P21 EXD provided more "speed, clarity, and slam," although Ken noted that he missed "the warmth and tone of [the Shindo's] lower-end fundamentals." His conclusion: "transparent, dynamic, and a serious truth-teller." Measurer-in-chief JA noted output impedance high enough to have audible consequences (of the nongood variety), plus higher-than-expected harmonic and intermodulation distortion: "I was disappointed by the BorderPatrol P21 EXD's measured performance." (Vol.41 No.7 WWW)

Jadis JA200 Mk.II monoblock: $33,900/pair
The JA200 Mk.II is an updated version of Jadis's original JA 200 (the space in the latter name is not a typo), a two-chassis, 160W monophonic tube amp that itself is no stranger to longtime readers of Stereophile. The new amp, based on the same circuit as its predecessor, is specified to deliver 160W into 8 ohms and is also divided between power-supply and signal boxes—that's four enclosures per stereo pair—but adds an important twist: In the JA200 Mk.II, the 10 output tubes are operated in auto-bias rather than fixed-bias mode. (The latter represents a confusing bit of nomenclature: a fixed-bias amp is one whose bias voltage requires periodic adjustment.) JVS noted that the pair of Jadis amps—20 output tubes in all!—put out less heat than his class-A Pass Laboratories XA200.8 monoblocks, and praised them for their total lack of noise. More to the point, Jason heard from the Jadis amps a sound that was "smooth, supremely well balanced, and captivatingly beautiful," though he noted that frequency extremes were not as well served as with his Passes, resulting in a lack of sparkle with some recordings, less impactful bass with others. With the JA200 Mk.II on his test bench, JA discovered very good squarewave reproduction and an absence of ringing, indicating "an excellent output transformer" (Jadis designs and winds their own); he also commented on the "high standard of construction." But he noted that the amp approached its rated output power only from its 2-ohm taps, and regretted its "poor linearity at high frequencies." (Vol.41 No.2 WWW)

Luxman MQ-88uSE: $5995 $$$
Luxman's limited-edition MQ-88uSE—only 100 have been made—is that rarity in contemporary high-end audio: a modestly powered tube amplifier unburdened by microprocessor-fueled gimmicks or a ghastly, massive, machined-aluminum case. The fixed-bias, push-pull, class-AB Luxman uses two KT88 pentode tubes per channel, operated as triodes, producing 25Wpc; ECC802 and ECC803 dual-triode tubes supply input gain and phase inversion. Power-supply rectification is solid-state, and output transformers, mains transformer, and power-supply choke are all designed and made by Luxman. The chassis is old-school minimalist, and a tube cage is supplied. The amp is mostly hardwired, and the build quality is first-rate. With the MQ-88uSE driving his DeVore Orangutan O/93 speakers, AD reported superb musicality—excellent musical momentum, flow, and pacing—and a sense of touch by which "every [harp] arpeggio was a tactile delight." AD's conclusion: "brilliantly musical and unmistakably high value . . . grab one while you can." In his Follow-Up, JA described the full set of measurements he made of the Luxman; his observations included higher-than-specified power (30Wpc into 8 ohms) and excellent squarewave reproduction ("a tribute to the high quality of its output transformers"). His conclusion: "an excellent example of a classic push-pull tubed design." (Vol.41 Nos.9 & 11 WWW)

McIntosh MC275: $6000 $$$ ★
The revived 75Wpc MC275 preserves the look of the original while adding modern innovations. Chimneys are used to cool the tubes by convection, and three circuit boards have been replaced by a single board on which are mounted all components, tube sockets, and power-supply parts. ST: "I heard all the dynamic quality, all that aliveness of the original, plus a level of transparency that brings the MC275 definitely into the 21st century." Sam bought the review sample. The fifth incarnation of the 75Wpc MC275, originally introduced in 1961, retains the first incarnation's classic appearance and its use of four KT88 power-output tubes, three 12AX7 input tubes, and four 12AT7 driver tubes. New are a stainless-steel chassis, balanced inputs, and gold-plated, five-way binding posts. While the MC275's two hefty transformers utilize the same "unity-coupled circuit" invented by McIntosh in 1947, the copper wiring is now insulated in a more durable synthetic material. Though dynamic expression was restricted and bass notes were "a bit muddy" in dense musical passages, the MC275 produced "stunning" soundstage depth and "spooky" intertransient silences, said FK. Meanwhile, the MC275's superb signal/noise ratios led JA to conclude that "Good audio engineering is timeless." Compared to its predecessor, the Limited Edition version of McIntosh's MC275 ($6500) has beefier binding posts, a more conveniently positioned power switch, and a gold-plated rather than stainless-steel chassis. In addition, a new output-transformer winding process has resulted in wider bandwidth, increased damping factor, and improved linearity. RD noted an ideal top-to-bottom tonal balance and an impressive sense of rhythmic drive, concluding, "The MC275LE is simply a wonderful-sounding amplifier, able to bring out the best from a wide range of loudspeakers." He bought the review sample. (Vol.27 No.7, Vol.33 No.10, Vol.35 No.10 WWW)

Music Reference RM-200 Mk.II: $7000 ★
Made in the US, the 100Wpc RM-200 Mk.II has the same basic physical and electrical architecture as the original, but uses better output transformers, adds a capacitor-forming function to extend tube life, and has a revised power supply. The fully balanced design features a high-power, bipolar, solid-state input stage and tubed driver and output stages. It uses two matched pairs of KT88 (standard) or 6550 (optional) output tubes, and a pair of 6BQ7 drivers. Though it lacked the slam and bass authority of more powerful solid-state amps, the RM-200 Mk.II produced airy highs, well-defined bass, and a lush midrange. "When the RM-200 Mk.II was in my system, I wanted for nothing," said MF. JA noted "superb measured performance for a tubed design." Now comes with hand wound output transformers; tube bias balance control, add $800. (Vol.34 No.12 WWW)

Rogue Audio Stereo 100: $3495
If you like tube amps and you also harbor a fondness for audio-frequency transformers, you may well love the Rogue Stereo 100, which greets the input signal with a Jensen line-level transformer—this as much to buffer unbalanced signals as to couple balanced signals that enter via the Rogue's XLR jacks—then hands off to dual-triode–based input and driver stages with a pair of KT120 output tubes per channel, operating in class-AB push-pull, with the user's choice of switch-selectable Ultralinear and Triode modes. The fixed-bias, solid-staterectified Stereo 100 outputs 100Wpc in Ultralinear, 60Wpc in Triode; in either mode, the Rogue kept HR's Harbeth M30.2 speakers "obviously well-tempered and well-nourished, power-wise. Both modes delivered detailed sound that was neither warm nor cool, just well balanced. The bass was tight and clean, maybe slightly lean, with no overhang or fuzzy harmonic additives." In measuring the Stereo 100, JA noted "superbly square" squarewaves in both modes of operation, and quite respectable signal/noise ratios, though power output was a bit lower than specified in both modes. Herb's conclusion: "the Stereo 100 is everything . . . that we could hope for in a 21st-century tube amp." (Vol.41 No.11 WWW)

Shindo Cortese: $13,500 w/F2a output tubes
The current version of Shindo Laboratory's only stereo single-ended amplifier—there are at least four different earlier versions, possibly more—uses a single Telefunken ECL82 pentode-triode tube per channel to drive a single F2a tetrode per channel in an autobias circuit. (A 300B version, priced at $12,995, is also available but remains unauditioned.) Distinguishing characteristics include the use of a rectifier tube (5U4GB) instead of a solid-state full-wave rectifier and the addition of an NOS Micromold Radio oil cap to the power supply's smoothing circuit—both of which have, at times, characterized earlier Corteses. Output power is specified as 10Wpc. AD noted generous gain—the Cortese is a three-stage amplifier—and, in general, the amp's ability to make music sound physically present, not to mention physically large, with sufficient bass extension and power that an orchestral bass drum on one recording "sent shivers down my spine." (Vol.43 No.2 WWW)

Shindo Montille 391: $7995 $$$
A somewhat more expensive variant of the company's entry-level amp, the Montille—which AD wrote about in the July 2007 Stereophile—the Montille CV 391 is a push-pull amp that coaxes 20Wpc from stereo pairs of the British CV 391 beam power tetrode. A true three-stage amp, thus blessed with generous gain, the Montille CV 301 uses 6AW8A triode-pentode tubes and 12AT7 dual-triodes as input tubes, as well as NOS Sprague coupling capacitors and Hammond output transformers. Shindo's second-least-expensive amp has a voice different from that of the company's more expensive offerings, but is no less musical—and in fact distinguished itself as one of the most vivid Shindos AD has heard, not to mention the one that is most comfortable driving 8 ohm rather than 16 ohm loads. (It sounded extraordinary through Art's DeVore O/93s.) Other Shindos may have more sophisticated or nuanced voices, but the Montille CV 391 is no less effective: Not only does this amp deserve Class A status, it offers conspicuously high value. (Vol.42 No.8 WWW)

VAC Statement 452 IQ: $75,000 stereo; $150,000/pair as monoblocks
Reviewed as a pair of monoblocks, MF marveled at "the relaxed and fully immersive presentation" from this massive, high-powered, cool-running amplifier, which uses banks of horizontally situated output tubes operated in class-AB using VAC's patented iQ Intelligent Continuous Automatic Bias System. Though he sometimes felt that these amps produced a picture that was too large for his room, the soundstage produced by a pair of these amplifiers on the Wilson Alexxes "was wider, taller, and especially deeper than anything I've ever experienced." MF also commented that "On the right recordings, the illusion of 'there' produced by this amp, thanks in part to the sensation of shimmering soundstage air, is extraordinary." Summing up, he wrote that the sound "was at all times coloration-free, exhibiting no frequency lumps or bumps and sounding refreshingly timbrally neutral, particularly from the midbass through the lower midrange, where I was expecting warmth and bloom. The bottom never sounded or felt sluggish or insufficiently extended, even on electrified rock, though its overall character was somewhat polite. The upper frequencies were addictively clean and pure, with faultless transient speed and clarity." The Statement 452 IQ is specified as delivering 225Wpc in two-channel mode or 450W in single-channel mode, both into 4 ohms. When he measured the amplifier as a monoblock, JA found that the VAC clipped at 235W into 8 ohms, but at 183W into 4 ohms unless he relaxed the definition of "clipping" from 1% THD+N to 10%, when the amplifier delivered 410W into 4 ohms. Fortunately, the VAC's distortion in the midrange and above was predominantly the subjectively innocuous second harmonic. Though he was bothered by what appeared to be modulation by the audio signal of the amplifier's noise floor, JA noted the amplifier's very low distortion in the treble at low-to-moderate powers into high impedances. (Vol.43 No.5 WWW)

B

Akitika GT-102: $488 (assembled); $314 (kit) $$$
As HR mused in his review of the solid-state AkitikA GT-102, "Jeez, Louise—should I even bother to drive a $7700 pair of [Joseph Audio Pulsar] speakers with a $488 amp?" That question is made more poignant by the fact that the GT-102 is available in kit form for only $314—far less than many of you would dream of spending on an interconnect or even a cable riser. To ensure that ours was an exemplary sample, for the sake of measurements if nothing else, HR tried a factory-built sample and found the 60Wpc GT-102, which is based on the same power op-amp as the well-regarded 47 Laboratory Gaincard integrated amp, had a "warmer, darker" sound than that of his Pass Laboratories XA25. The AkitikA didn't make much headway with the difficult-to-drive Magnepan .7 planar-magnetic speakers, but it partnered well with Falcon Acoustics' LS3/5a minimonitors, Herb being especially impressed by "how attractively it rendered the complex harmonic structures of . . . saxophone, harmonica, violin, and marimba." His conclusion: "Super-highly recommended." Writing from his lab, JA noted that the AkitikA "is happier driving higher impedances, though this drawback must be considered in the context of its very affordable price." (Vol.41 No.7 WWW)

Balanced Audio Technology VK-56SE: $8495
This three-stage, push-pull, fully-balanced amplifier uses one pair per channel of the Russian 6C33C triode to produce 55Wpc into 8 ohms—110W when bridged for mono—all in class-AB mode. As the company name might lead one to expect, inputs are balanced (XLR) only—adaptors are available, from BAT and elsewhere, for users with single-ended-only preamps—and output connectors are provided for low-, medium-, and high-impedance loads. The 52lb BAT won HR over with "a force-filled liquid vividosity that presents itself with the scale, detail, and color saturation of 70mm film" and described its characteristic sound as "liquid and clear, effervescent, and richly toned," although he said the amp lacked a bit of "boogie" with the Magnepan .7 (a notoriously current-hungry load). At the test bench, JA was bothered by what he described as the amp's "high output impedance." (Vol.42 No.6 WWW)

Cary Audio CAD-805RS monoblock: $15,995/pair
On the cover of the January 1994 Stereophile, the original Cary CAD-805 monoblock—a single-ended triode amp that offered 27Wpc—posed next to a 300Wpc Krell amplifier; above them, a headline fairly taunted: "If either of these amplifiers is RIGHT . . . the other must be WRONG." A quarter-century later, that Cary monoblock endures as the CAD-805RS. Now as then, the user can select between a single 845 or 211 output tube: both are supplied, and both deliver 27W in class-A, which is how this amp operates under most conditions. But when more power is required the Cary slips into class-A2, and there the output tubes differ, the 845 delivering up to 50W for short durations, the 211 up to 70W. The CAD-805 offers adjustable global feedback (010dB), apparently high voltage gain, and separate output taps for 4, 8, and 16 ohm loads. In his listening observations, AD expressed a preference for the 845 tubes, but noted from both tube types a bass range that was slightly too generous but nonetheless sublime, giving impact and taut tone to timpani and rewarding him with electric-bass lines that were always engaging and never sluggish. Consistent qualities were believably rich timbral colors and textures and spatial performance in which "centrally positioned voices and solo instruments popped forward from the mix . . . [with] pure, not-unexpected single-ended magic." Reporting from his test bench, JA noted output impedance that was "relatively low for a single-ended triode amplifier," yet also confirmed that load-impedance–related modulation of the amp's frequency response resulted in a low-bass boost. (Vol.42 No.1 WWW)

EleKit Tu-8600RS: $1785 as reviewed ($1185 basic version)
As the name suggests, the EleKit TU-8600R is a build-it-yourself power amp, a single-ended design that uses one 300B directly heated output tube per side for a specified output of 9.2Wpc at 10% THD. (A pre-assembled version is available at extra cost.) Prices start at $1185 without tubes and top out at a $2985 version that includes Lundahl output transformers and deluxe German-made Elrog 300B tubes. Herb Reichert tried a variety of 300Bs in his Lundahl-equipped review sample and praised the EleKit for sounding not warm and soft but "fast and vigorous, as transparent as any amplifier, and extremely captivating," with a sonic character that's "clean, neutral, and precise." HR's conclusion: "This is what I call value for money." Other kits are available, but availability is sporadic. (Vol.42 No.4 WWW)

Emotiva XPA-2 Gen3: $999 (two-channel version) $$$
The XPA Gen3 is a modular class-H amplifier—its input stage tells its power-supply stage when and when not to stoke the fires of its output stage—but it isn't just a stereo amp: it can be ordered with anywhere from two to seven channels. (The two-channel version costs $999; each additional channel adds $200 to the price. Channels can be added only by Emotiva or an authorized Emotiva dealer.) HR tried a two-channel XPA Gen3—300Wpc into 8 ohms, 550Wpc into 4 ohms—with a variety of different speakers. The pairing with Zu Soul Supremes was less than dreamy, but listening to Miles Davis through the hard-to-drive Magnepan .7s, Herb wrote that "the bell of his trumpet was right there in front of me," and observed that the Emotiva "held and guided the Magnepan .7s with almost a lover's touch: not too tight, not too loose." Then again, through the Technics SB-C700S speakers, the sound of the Emotiva had HR reaching for words like "hard" and "transistor sound." In measuring the XPA Gen3, JA discovered that the percentage of THD+N climbed "precipitously" above 15kHz, though he acknowledged that it offered very high power "at a very affordable price." (Vol.40 No.8 WWW)

First Watt SIT-3: $4000
Designer Nelson Pass commissioned a now-defunct maker of semiconductors to produce for him an exclusive run of static induction transistors (SITs), and the limited-edition (250 units) SIT-3 may prove to be the last amplifier created to use them. The SIT-3 is a single-ended amp in which the input signal has its voltage gain boosted only by an onboard step-up transformer; the amp's single active stage provides only current gain. The product of all this simplicity is a decent enough 18Wpc, but with less gain (11.5dB) than most other amplifiers. HR tried the SIT-3 with a variety of loudspeakers and declared it "a modestly priced masterpiece" and "one of the two or three finest-sounding amplifiers I've heard anywhere, at any price." JA's measurements did nothing to dispel that notion: "Although [its] relatively high level of second harmonic distortion, which is a deliberate design choice, is controversial, the First Watt SIT-3 is a well-engineered amplifier." (Vol.42 No.2 WWW)

Margules Audio U280-SC Black: $8000 (stereo), $15,000/pair (monoblock)
Designed and built by a family-owned company in Mexico City, the Margules U280-SC Black is a tubed amplifier that uses a total of four KT88-family power pentodes. The amp is switchable between stereo and monoblock modes, and between Ultralinear and triode operation, with these power outputs: Ultralinear stereo, 60Wpc; triode stereo, 30Wpc; Ultralinear mono, 120W; triode mono, 60W. In all settings, power-tube performance is monitored and maintained by an Active Servo Control bias technology, hence the SC in the model name. JVS used a pair of Margules amps in monoblock mode to drive his Wilson Alexia speakers and a pair of Harbeth M40.1s, and found the latter to be the far better mates. At their best, with the Harbeths, the Margules amps rewarded Jason with "colors [that] were naturally and ideally saturated," and "believable" timpani attacks. His conclusion: "a wonderful class-A tube amp whose modest power output belies its ability to deliver one grand, splendid performance after another." But when the Margules amp took its place on the test bench, JA's eyebrows rose. He "was not impressed by the . . . U280-SC's measured performance when it was used as a conventional stereo amplifier." That said, JA's measurements uncovered lower distortion and higher power when the amp was operated as a monoblock. (Vol.40 No.11 WWW)

Editor's Note: There are no amplifiers listed in Class C and D.

Deletions
Mytek Brooklyn AMP replaced by new version not yet reviewed. PrimaLuna Prologue Premium discontinued. AudioNet Max monoblock, Ayre Acoustics MX-R Twenty monoblock, Bricasti Design M28 monoblock, First Watt J2, not auditioned in a long time.

COMMENTS
partain's picture

I can't stand it !
Please review the new & improved KEF LS50s.
The things I've read are titillating , to say the least.

John Atkinson's picture
partain wrote:
Please review the new & improved KEF LS50s.

There is a pair of the new KEF LS50 Meta on its way to me.

John Atkinson
Technical Editor, Stereophile

Link's picture

Awesome, looking forward to the review. Wireless or passive? Just curious what to expect. Thanks.

John Atkinson's picture
Link wrote:
Awesome, looking forward to the review. Wireless or passive?

Passive.

John Atkinson
Technical Editor, Stereophile

rk11's picture

Auditioned the KEF R3s, Polk Legend L200s and the KEF LS 50 Metas a few days ago with 5 tracks of my choosing and thus far my rank ordering of these speakers is as noted. Personally, I found the Metas a bit bright and their bass response was the most lacking - not surprising given the size of the speaker cabinet. Never been a fan of the Polk speakers till the Legend series. The 200s were every bit as good as the R3s EXCEPT in the vocals. I am sure that JA's review will be under a much better controlled environment.

Shangri-La's picture

In the written review, the Ares II was preferred over the Chord Qutest. Yet the Qutest is rated Class A and Ares II is Class B. Interesting...

LinearTracker's picture

BD gave the Duo an “A” rating and deservedly so, but I am listening to the new Duo with the linear power supply and believe it to be a game changer.
I hope to see an update soon.

Link's picture

I have been able to compare the BRXs to a true class A speaker in my system, and I do now agree with the class B rating. Thanks again for the great reviews.

Glotz's picture

with explanation...

Link's picture

Comparisons having been done, the BRXs are nothing to shake a 1M interconnect at. Although they are not quite up there in terms of transparency, detail, and air - they sure do get the timbre, neutrality, and imaging right.

thyname's picture

You butchered the name of T+A MP 3100 HV. Please fix it. There is no such thing as “ T+A MD 3001 HD SACD/CD player: $21,000”

Robin Landseadel's picture

The "A" rated Sennheiser HD 650 headphones have been reissued at a lower price [with a couple of changes that don't affect the sound] as the Drop HD 6XX. Drop is an online only operation, sells for $220 + shipping & tax. It's one of the cheapskate audio high points of the season along with Topping Headphone amps and DACS.

X