Analog Corner #312: WallyTools & the WallyReference Page 2

Remember that if your tonearm has an offset headshell, VTA/SRA and azimuth adjustment will be interrelated so that adjusting one affects the other. I believe that often, when people claim to hear a big sonic difference when they make minute VTA/SRA changes, they're instead hearing the effects of an azimuth change. The relationship is well spelled out in the WallyReference manual. WallyTools supplies the tools necessary for adjusting various arm configurations, whether azimuth adjustment is carried out at the headshell or on the armtube.

Set SRA using a USB microscope
Setting SRA to 92.5° (which more often than not produces 92° under dynamic, spinning-disc conditions) is best done with a microscope. I use a now-discontinued Dino-Lite 330 mounted on a gooseneck stand, with the supplied software. I've learned how to get the most out of it, despite its shortcomings.

821acornw.usb

I haven't got enough space to go into detail here, but you'll find details in profusion in the video on the WallyTools website. If you want details, lots can be found by clicking on the "At Home SRA Analysis Instructions" button at the bottom right of the page. I recommend you also watch the Webinar Video (button bottom left). Getting accurate measurements requires you to follow certain guidelines, which are spelled out in the video. This procedure has a fairly steep learning curve, but it's well worth the effort. Avoid anxiety by using an inexpensive cartridge your first time.

821acornw.angle

I've seen close-up "macro" digital photos taken by readers that when "blown up" were of sufficient resolution and accuracy that, when used with a plastic protractor placed against the screen, could determine whether a cartridge has been incorrectly manufactured so that 92° would be impossible to achieve. That methodology can often get you in range of proper SRA, though the microscope approach is better. This is critically important information, especially if you've invested five figures in a cartridge.

With SRA set to 92.5°, I recheck VTF and then, with antiskating off, use the new WallySkater (a seriously upgraded version of the one I used in Copenhagen) to be sure the arm is not applying horizontal (antiskating) force (see cantilever skew story above).

821acornw.trac

Then I use the WallyTractor Universal protractor to set overhang and zenith angle using Löfgren A alignment (for the SAT arm I use its similar, arc-type gauge). I find it reassuring to see the stylus riding in the arc's groove across the entire surface of the tool rather than sitting correctly in either a single "null" point or even in both null points. The WallyTractor has a second set of arcs, which is useful if your collection includes many recently produced records that aren't cut almost to the label. WAM Engineering claims that when used for a newer record collection, these arcs can reduce linear tracking error by 25% and produce distortion measurements typical of a 12" arm from a 9" arm—not that I think 9" arm distortion is an issue.

821acornw.skat

I now check VTF again then use the new, improved WallySkater to set antiskating. To learn more about With antiskating "off," the plumb bob and finger lift should align. When the added antiskating force moves the arm toward the platter's outer edge and produces between 10 and 12 deviations on the scale, "antiskating has been set correctly. (There's a secondary check that I won't go into here.)

Finally, I set azimuth using a digital oscilloscope and the Analogue Productions Ultimate Analogue Test LP. The second and third bands on Side 1 provide left-channel-only and right-channel-only 1kHz-modulated grooves. Theoretically, the unmodulated groove should produce 0 volts, but there's always crosstalk.

To do this correctly, it's best to use a solid state phono preamp with dependably identical output for each channel. The phono preamp output must be connected to the oscilloscope probes. There are various ways of doing that including something as simple as wiring up a pair of chassis mount RCA jacks with bare loops on the unsoldered end, to building an interface box or having one built for you as I did.

821acornw.osc

The digital oscilloscope takes voltage readings 16 times a second and produces a reliable average. My Instek GDS-1022 cost around $400, but it was discontinued and replaced with the far more compact GDS-207, which costs $700; you can find other, similar 'scopes online for around $350. The specific measurement procedure varies among oscilloscopes, but the goal is to adjust the azimuth so that the crosstalk is minimized and equal in both directions, L–R and R–L.

You can also use a high-quality dual-channel voltmeter, preferably with a large analog meter like the Leader LMV-89 that Soundsmith's Peter Ledermann recommended to me. You'll get more accurate channel-separation measurements using the voltmeter, but for the purposes of setting azimuth (as opposed to assessing a cartridge's actual channel-separation specs), the digital oscilloscope is just as good.

If you go the dual-channel voltmeter route, you'll need to insert two "short filter cable interrupts" (as Ledermann called them) that filter from 30Hz down (–3dB at 30Hz, –6dB at 15Hz, –12dB at 8 Hz) to get rid of some of the rumble.

I take five readings, starting with the headshell tilted approximately 2° to the left and ending with it tilted 2° to the right. Each measurement produces a large voltage from the modulated channel and a small voltage from the unmodulated channel. After converting the voltage to dBV (decibel-volts) and subtracting the smaller voltage from the larger one, you get two sets of crosstalk figures, one L–R and one R–L.

One of the five sets of measurements will produce maximum separation and minimum crosstalk. That might be the correct final azimuth setting, but unless the two sets of measurements are identical (ie, 28dB L–R and 28dB R–L), which doesn't often happen, it's best to take at least two more readings, one on either side of the best of the first five measurements, shifting azimuth slightly in either direction, and then settling on the best one.

How do you know when it's good enough? A 2dB difference between the L–R and R–L measurements is considered more than sufficient, although occasionally you can get an identical measurement in both directions. And sometimes that can be achieved when the headshell is in its parallel-to-the–record-surface position, though that almost never happens (it happened once to me with the original Lyra Etna SL), which is why setting azimuth by setting the cantilever perpendicular to the record surface isn't good enough.

Zenith
Not long ago, I sent a phono cartridge to J.R. Boisclair for inspection. He discovered a zenith angle error—that's the alignment of the stylus's contact edges, which we cannot see, relative to the cantilever, which we use to align for proper offset angle—of more than 2°. He compensated for the zenith-angle error and heard an easily audible improvement. He told me he produced a blind test using volunteers, who corroborated what he heard.

821acornw.zen

Boisclair returned that cartridge to me along with a new tool, the WallyZenith, which features zenith-angle hashmarks etched at various deviations from perpendicularity to the cantilever. It's only useful if you've had your cartridge examined. (Boisclair says he's not quite ready for "assembly line" zenith-angle stylus inspection.)

All this may seem extreme, but it takes less time to go through this process than you might think, and it's worth any reasonable amount of trouble to eliminate guesswork.

821acornw.done

When you're done, unless you slipped up, there will be no surprises. The first thing people say when they hear a cartridge that's correctly set up is either that finally they don't hear mechanical artifacts or that their turntable has never sounded so spatially and timbrally well-balanced.

For Rega Arm Users
BTW: Rega's three-point cartridge mount produces a Stevenson-type alignment, which I consider measurably and sonically the worst because while it minimizes distortion at the end of the side, it produces far greater distortion than Löfgren A over almost the entire rest of the record. Rega owners should try Löfgren A. If you don't like it, it's easy enough to screw in all three screws and return to the factory setting.

Rega Research values rigidity over adjustability and considers setup parameters other than VTF, overhang, and antiskating unimportant. Their case for rigidity is strong; I'll even admit that less adjustability is better than a complete but sloppy adjustability. I've also heard a good "best mechanical performance" case made for having the stylus sitting perfectly centered in the groove even if it results in an electrical imbalance, rather than setting azimuth electronically, but in my experience, on a well-designed and -constructed arm, setting all parameters as described here delivers the best performance.

WallyTools offers the WallyFulcrum, an azimuth adjustment tool for Rega arms made of a highly rigid material offering a "solid union between cartridge and tonearm" that changes azimuth angle in increments as small as 0.25°. When you adjust azimuth at the headshell, SRA is not affected.

One final Rega-related setup tip: While Rega arms do not offer VTA/SRA adjustability, Acoustic Signature manufactures easy-to-use three-point SRA-raising shims that require only that you loosen the three arm mounting screws (footnote 1). You don't have to remove the arm (though if you need all of the shims, the hinged cover supplied with the less-costly Regas won't close). To lower SRA, try a thicker mat, like Funk Firm's 3.5mm or 5mm Achromat platter mat: Raising the front of the arm has the same effect as lowering the rear, but you already knew that. The Achromat sounds much better than the supplied felt dust attractor.


Footnote 1: Note, however, that Rega strongly discourages the use of aftermarket shims with its top turntable, the Planar 10, because its light-and-rigid plinth material can crack.—Editor
ARTICLE CONTENTS

COMMENTS
Anton's picture

Also, good motivation to consider SPU units.

I admit to having reached a point that is proximal to the point of "this is more work than fun."

I think I am about one groove width away.

Ortofan's picture

... the cartridge body is properly aligned in the tonearm and that overhang is correct.
It can't compensate, or allow adjustment for, a stylus that is misaligned on the cantilever and/or a cantilever that is misaligned in the cartridge body.

tonykaz's picture

"Back in the day" I sold tons of this type of stuff at my Esoteric Audio Vinyl Salon. I had a complete Wall of Monster Cable Accessories too.

These are great little Cash Sales that can represent half of the Daily Sales for a Retail outfit like us. ( mid 1980s )

Of course we didn't have Streaming's dominant 83% Market Share to contend with.

and..

We didn't have to share media Sales with CDs like today where CDs and $30 Vinyls are neck and neck, sharing 6% of the Phisical Media Dollar Sales!

---

We did have Cassette for what it was....

but we didn't have Vinyl gear costing the price of Cars.

Ahhhhhh those good old days...

Tony in Venice Florida

ps. remember when we could buy limited Edition pressings of Sheffield Labs?

Ortofan's picture

... Telarc recordings on cassettes?

tonykaz's picture

Yes, I recall the incredible excitement involved with Cassettes and the high performance Nakamichi Decks. ( I wasn't one of their Dealers )

If I still owned a Nakamichi Dragon today, I might be trying to keep Tape alive like the 33.3 people are trying to do with Vinyl.

Unlike 33.3, Cassettes worked well for people with a Full Ambulatory Life-styles. ( me with handfuls of favourite travelling Cassettes )

However, Apple iTunes switching to High-res w/MQA & the proliferation of affordable Digital Audio Players pretty much kills a high percentage of future Cassette or 33.3 investments. ( and Tidal too if I'm hearing rumours correctly )

I wonder :

Will the $300 iPad mini become the latest & greatest portable music player?

Cassettes to DAPs: We've come a verrrrrrryyyyyyyy Looooooooonnnnnnnnnnggggggggg way in such a short time !!!

This next Decade is gonna be a THRILLER for progressive Audiophiles and the Music Manufacturing Industry. These next Audio Shows will be exciting.

I'm bracing myself

Tony in Venice Florida

Jack L's picture

Hi

I got 1978 Telarc digitally mastered LP: "Frederick Fennel: The Cleveland Symphony Winds". it sounds pretty acceptable to my criticl ears considering it was only 16bit/50KHz Soundstream recording format back then.

Yet, the 2 CDs also Telarc: "Beethoven Symphony No. 9" (1985) & "Tchaikovsky 1812" (1979) which I got do not impress me at all.
I heard other CDs of same music titles which I own sound much better
Using the same 24bit/192KHz DAC.

Listening is believing

Jack L

mcrushing's picture

These tools are cool but roughly exceed the cost of my cartridge. VTF gauges, USB scopes and protractors are fortunately cheap in this Age of Amazon... For me, azimuth is the tricky thing.

Michael, I wonder if you'd comment on my method. It's similar to yours, but lacking oscilloscope or fancy voltmeter, I use my iphone and a free SPL meter app.

I first get the stylus as vertical as possible using the USB microscope. Then with phone and each speaker equidistant, I play a "balance test" track (1 kHz tone modulated one channel at a time) and measure the SPL of the crosstalk in the opposite channel. I adjust azimuth and repeat the process until the crosstalk levels are as equal as I can make them. I then use each tone in its proper channel to reset the balance knob. In theory, the difference in dB between the full-blast tone and the crosstalk tone in each channel should roughly tell me what my channel separation is – but this number tends to be MUCH higher than the manufacturer's spec. This has me suspicious.

This being a tedious process, do you think an iphone running the dB Meter app is accurate enough to use for this purpose, or am I wasting my time?

Jack L's picture

Hi

All roads lead to Rome.

Some can afford a Mercedes. But you don't have to follow.
I can always afford one but I don't want to spend the huge ongoing garage maintenance fees. So I own an all-wheel drive made in Japan, excellent for tracking icy roads up in the North here for 20 years now. Affordable but save driving.

Likewise, some TT/tonearm/cartridge alignments done is better than nothing.

My homebrew way is even simple & sorta 'primitive'. No need whatever
band-name expensive scientic tools. The first thing first : to ensure the whole TT is spinning perfectly level : surprised I seldom read this TT ABC mentioned in any TT/tonearm/cartridge alignment reviews. In fact, this 100% TT levelling is so easily taken for granted. I always get a featherweighted bulleye spirit level indicator on my TTs. Check the speed of the TT with a stroboscope disc to ensure correct spinning speed. I don't think our ears can detect micro-decimal speed variation. Let's be realistic.

Simple paper tracking protractor to align correct stylus position.
Small bead spirit leveller placed on top of the tonearm tube to ensure tonearm/cartridge parallel to the record surface. The most critical test, IMO, is to ensure the stylus is touching the record all-direction level. My simple way is to place the same round featherweight spirit bulleye leveller on top of hardshell indicating DEAD centre spirit bubble position. Done !

Go without saying : digital stylus tracking pressure & anti-skating alignment using blank groove tracking test record.

So simple, easy & efficient. I repeat such test frequently.

This homebrew thing works fine in tracking my some 1,000 LPs,
99.5% preowned from theft stores. If I can hear the soundbox articulation difference between the young L. Pararotti & Mario del Monaco, I believe my simple tracking method works big time.

Listening is believing

Jack L

~

Old Audiophile's picture

Please excuse this, no doubt, very basic but, I think, very practical question.

For those of us who love vinyl and do not own uber-expensive turntables (say... something in the 3 to 5 thousand dollar range, US) or all of the gauges & gadgets necessary to precisely mount a new cartridge or check the installation of our own, how would one go about finding a trusted expert who could do that for us? Would this be as simple as taking our TT to a trusted high-end shop? Is there a price point below which this level of precision is superfluous? Do most manufacturers do a good job mounting cartridges bundled with the TT's they sell? In fair comparisons of well recorded and well engineered recordings of the same CD and vinyl albums, is the fact that I invariably prefer vinyl over CD any indication that my cartridge is probably set up correctly?

Mike, do you make house-calls? I'm not that far away and I make a mean barbecue! I also usually have a fine single malt on hand.

Jack L's picture

Hi

Don't sound so helpless! "Old" guy (I am "old" too by age).

Read my post just above yrs & get it done yourself so sweat.

The level indicators are available instore or online from any hardware & auto parts stores dirt cheap.

Take it easy. The sky is not falling down.

Jack L

shawnwes's picture

One simple way to check if your turntable is set up close to ideally is to use a turntable set up disc such as the one Acoustic Sounds sells. Easy to use and will confirm if the basic setup is accurate. It's about $40. Here's a link to the one I've mentioned: https://store.acousticsounds.com/d/35532/Analogue_Productions-The_Ultimate_Analogue_Test_LP-Turntable_Set_Up_Tools

There is a fellow in the New York area name Michael Trei who does offer set up services. He's considered one of the best. I have no idea what he might charge. The only contact info I have for him is via Facbook: https://www.facebook.com/michael.trei

mcrushing's picture

Thanks, Jack L. I'm maybe overthinking azimuth, but I'm positive the effort I've put into DIYing my setup pays off in sonics, and in a better understanding of how all this works. If you're the sort who's reading this comment you'll likely be glad you tried it, even once.

To Old Audiophile's specific questions, here's my $.02:

I think setup is critical at all price points/levels of high-end-ness. (It'll also better preserve your records.) If your table came with a pre-installed cartridge, it's reasonable to assume the setup was done correctly, IMHO. But in the $3-$5k range you mention, it's also *very* reasonable to expect the retailer to confirm that.

Even then, you're still at the mercy of entropy once you get it home. For some reason – or perhaps thousands of tiny, accumulating reasons - your setup may drift over time. For me, the ability to self-diagnose that is worth the price of admission. Your mileage (and interest in futzing with microscopic objects) may vary.

Most dealers I know of will do setups for a nominal fee or even for free. One may even be willing to let you watch. I'd just call around and find one you click with. Or perhaps Mikey will be enticed by your kind offer of liquor and BBQ. Although the story he tells in the lede of this column sounds less like a house call and more like a kidnapping...

mdiaz0429's picture

I cant afford to pay for your trip to Georgia like the guy did in Poland to his home, but I wish I could afford it...

X